Use the adhesive the professionals use for protecting the PCB when using hot air during repairs and insulating electronic components

Polyimide brown metallic masking tape (also known as Kapton) for protecting areas from high heat.

Features:

• 10mm thick
• 30m length
• Material: Polyimide
• Short Term Temperature Resistance: 300°C max
• Long Term Termperature Resistance: 260°C max
• Responsive to demanding environmental conditions
• High Temperature masking
• Excellent electronic insulation
• Leaves no residue

• Colour - Brown Mettalic
• Total Width - 10mm
• Total Length - 30 metres
• Total thickness - 2.5 mils
• Elongation at break - 60%
• Tensile Strength - 30 lbs/in
• Short Term Temperature - 300°C max
• Long Term Temperature - 260°C max
• Temperature Range - (-73°C - 260°C)
• Storage Conditions - Dry place (13°C - 30°C)

• 1x 10mm Kapton Polyimide 30 metre roll

Use the glue the professionals use for sticking down glass and various plastics on mobile devices.

Appearance: transparent semi-fluid
After curing Hardness: 70-85B
Surface dry time: 3 minutes
Full cure time: 24-48 hours
Storage: stored at 10 degrees to 28 degrees
Shelf Life: 18 Months


Please read carefully before using:

1. The optimum operating temperature should be between 18-32 degrees
2. Experiment on a small area before using on a large surface
3. Make sure that the surface is clean and dry before applying
4. Apply an even amount of glue on the surface.
5. Position two surfaces together and apply pressure for 2-5 minutes
6. Please allow up to 48 hours for optimum adhesive strength

Compatible with:

• Glass
• Plastic
• Acrylic
• Rubber
• Leather
• Ceramics
• Rhinestones
• PE
• PP
• PVC
• ABS

• 1x 15ml T8000 tube of liquid glue

Use the adhesive the professionals use for protecting the PCB when using hot air during repairs and insulating electronic components

Polyimide brown metallic masking tape (also known as Kapton) for protecting areas from high heat.

Features:

• 15mm thick
• 30m length
• Material: Polyimide
• Short Term Temperature Resistance: 300°C max
• Long Term Termperature Resistance: 260°C max
• Responsive to demanding environmental conditions
• High Temperature masking
• Excellent electronic insulation
• Leaves no residue

• Colour - Brown Mettalic
• Total Width - 15mm
• Total Length - 30 metres
• Total thickness - 2.5 mils
• Elongation at break - 60%
• Tensile Strength - 30 lbs/in
• Short Term Temperature - 300°C max
• Long Term Temperature - 260°C max
• Temperature Range - (-73°C - 260°C)
• Storage Conditions - Dry place (13°C - 30°C)

• 1x 15mm Kapton Polyimide 30 metre roll

Replacement screens are very expensive and can seem like such a waste when only the glass is cracked on your phone. Learning glass only repairs can be very lucrative and save a lot of money if you have the right tools. Whether you're using expensive equipment to refurbish your screens or using LOCA for a quick repair, you'll need to use this cutting wire for the seperation part of the job.

 

Features Include:

• 1mm thick Alloy Steel Molybdenum material
• 100m long
• Strong and durable
• Easy and Fast to use
• Comes with two handles so you don't cut your hands on the thin wire
• Perfect for seperating the glass from LCD on iPhones, Samsungs, iPads, Apple Watches and more

Type: Molybdenum Cutting Wire
Length: 100 Metres
Thickness: 1.0mm
Material: Alloy Steel

• 1x Roll of 1.0mm Moybdenum Cutting Wire (100m)
• 2x Handles

The Isopropyl alcohol wipes are a must have around the work station, easily wipe bits of dust away prior to sticking down an iPad screen, clean areas that have stubborn adhesive debris or use to clean the surface of the device. So versatile and handy 

 

Features:

• Individually wrapped
• 70% Isopropyl Alcohol
• Cleans, disinfects and dissipates within 30 seconds
• 3 year shelf life
• Size 50mm x 50mm

All electronic and mechanical devices

• 100x Isopropyl Alcohol Pad Wipes

Replacing screens can be expensive. If you want to keep the original screen, the cheapest option is to replace the glass and install the new screen with LOCA glue. LOCA is a liquid form of the Optical Clear adhesive that is already on your screen. It spreads easily and cures under a UV light in just 3 minutes.

UV LOCA hardens in about 30 seconds, but is recommended a cure time of about 3 minutes for a strong hold. Sun light can be used too, but it will take a bit more time to cure.

• Professional UV LOCA glue
• 10mL
• Glues replacement glass to screens
• Hardens with standard UV light

 

Instructions for use:

1. Remove broken glass and clean off old glue residue
2. Place LCD in mold
3. Apply 1.5g UV glue in the middle of LCD screen
4. Place glass replacement onto screen and let glue settle to the corners, adjust slightly if need be.
5. Place screen under UV light for 3-5 minutes for full cure

 

Please Note: Do not use a fluorescent light while bonding. Fluorescent gives off UV light, enough to slowly cure the glue. For longer work times work under a regular light bulb, or LED lighting. 

Please Note: Do not store under direct sunlight, it will harden in the tube. Store in dark drawer

• Type: TP-2500
• Size: 10mL
• Validity Period: 3-6 months
• Storage Temperature: 5-35C RH<70% (store in dark room or drawer)
• Cure Method: UV light
• Viscosity: 2500 mPa·S
• Transmission: >99%
• Cure Time: 3-5 minutes
• Suitable for mobile and electronic screen replacement

• 1x UV LOCA 10mL tube

The Mechanic UVH900 High Quality UV green Solder Mask is widely used for mobile phone, computers and other electronics for running new tracers (or jumpers) Once you have positioned the jumper, cover it with Mechanic green UV solder mask and cure with a UV light. You will then not have any issues with shorting.

UV curable solder mask is non-conductive and won't dry up in the tube like traditional conformal coating. Even better, it has a virtually unlimited working time until UV light is applied to cure and dry the solder mask. Perfect for protecting trace repairs and covering up jumper wires.

• Professional Mechanic UVH900 UV Green Solder Mask
• 10mL
• Insulates printed circuit boards against shorting and arcing
• Protects exposed PCB traces from corrosion and moisture
• Insulates new PCB traces and jumpers
• Used with standard UV light

• Brand: Mechanic
• Model: UVH900-GY
• Size: 10mL
• Cure Method: UV light
• Suitable for mobile and electronic repair

• 1x Mechanic UVH900-GY Green UV Solder Mask
• 1x Plunger
• 1x needle

The Mechanic XG-80 (now known as XGSP80) High Quality Solder Welding Paste is widely used for mobile phone, computers and other electronic chips for repair and maintenance. Designed with high-grade rich solder, it has no faulty soldering so you can be confident when repairing

• Professional Mechanic XG-80 Solder Paste
• 183℃ melting point 
• 60g tub
• IPX3 flux
• Sn63/Pb37 Alloy

• Brand: Mechanic
• Model: XGSP80 or XG-80
• Alloy: Sn63/Pb37
• Microns: 25-45um
• Flux: IPX3
• Weight: 60g
• Melting Point: 183℃
• Suitable for mobile and electronic repair including BGA reballing

• 1x Mechanic XG-80 Solder Paste

Use the adhesive the professionals use for protecting the PCB when using hot air during repairs and insulating electronic components

Polyimide brown metallic masking tape (also known as Kapton) for protecting areas from high heat.

Features:

• 20mm thick
• 30m length
• Material: Polyimide
• Short Term Temperature Resistance: 300°C max
• Long Term Termperature Resistance: 260°C max
• Responsive to demanding environmental conditions
• High Temperature masking
• Excellent electronic insulation
• Leaves no residue

• Colour - Brown Mettalic
• Total Width - 20mm
• Total Length - 30 metres
• Total thickness - 2.5 mils
• Elongation at break - 60%
• Tensile Strength - 30 lbs/in
• Short Term Temperature - 300°C max
• Long Term Temperature - 260°C max
• Temperature Range - (-73°C - 260°C)
• Storage Conditions - Dry place (13°C - 30°C)

• 1x 20mm Kapton Polyimide 30 metre roll

Use the flux the professionals use for PCB and logicboard repair.

This solder paste is a high viscosity no-clean flux, it can be used for PCB, SMD, reworking, and for soldering and reballing of computer and phone chips. 

It is a high-quality flux paste made from a mixture of transparent rosin, organic acids, antioxidants, preservatives, organic solvents, etc. It doesn't leave pale yellow residue so you can easliy clean the board after use.

 

Brand: Amtech

Manufacturer: Jiyang Solder
Type: NC-559-ASM
Size: 10ml
Use: Suitable for BGA, PGA, CSP packages and flip chip operation as well as PCB reflow

Feature: No-Clean, Lead-Free

 

You can check our Amtech Jiyang Solder products are genuine by going to the Jiyang Solder website and typing in the serial number

All electronic soldering repairs including BGA, PGA, CSP, flip chips and PCB reflow

• 1x 10ml Amtech NC-559-ASM Lead-Free No-clean soldering flux
• 1x Piston push bar
• 1x needle

Use the glue the professionals use for sticking down glass and various plastics on mobile devices.

Appearance: black semi-fluid
After curing Hardness: 60-80B
Surface dry time: 3 minutes
Full cure time: 24-48 hours
Storage: stored at 10 degrees to 28 degrees
Shelf Life: 14 Months


Please read carefully before using:

1. The optimum operating temperature should be between 18-32 degrees
2. Experiment on a small area before using on a large surface
3. Make sure that the surface is clean and dry before applying
4. Apply an even amount of glue on the surface.
5. Position two surfaces together and apply pressure for 2-5 minutes
6. Please allow up to 48 hours for optimum adhesive strength

Compatible with:

• Glass
• Plastic
• Acrylic
• Rubber
• Leather
• Ceramics
• Rhinestones
• PE
• PP
• PVC
• ABS

• 1x 15ml T7000 tube of liquid glue

The Dust free cleaning wipes are a must have around the work station, easily wipe bits of dust away prior to sticking down an iPad screen, soak in isopropyl alcohol to clean stubborn areas or use to clean the surface of the device. So versatile and handy 

Features:

• Vacuum packed
• Polyester wipes
• Excellent absorbency
• Dust and partcile free
• Doesn't leave dust or water stains
• For dry and wet use
• Class 1-10000 clean room
• Size 95mm x 95mm

All electronic and mechanical devices

• 50x Dust Free Cleaning Cloth Wipes

Use the adhesive the professionals use for sticking down glass, plastics and cables on mobile and tablet devices. This is a popular tape used by OEM phone and tablet manufacturers

TESA 61395 is a black, double sided self-adhesive tape consisting of a black PET backing and tackified acrylic adhesive.

 

Features:

• 1mm thick
• 30m length
• Thickness: 200µm
• Very high bonding strength
• Superior resistance
• High shock resistance
• Responsive to demanding environmental conditions
• Black color for easy detection
• Pressure activated - heat is not required to form a bond

 

• Back Material - PET film
• Colour - Black
• Adhesive Type - Tackified Acrylic
• Total Width - 1mm
• Total Length - 30 metres
• Total thickness - 7.87 mils
• Elongation at break - 50%
• Tensile Strength - 11.42 lbs/in
• Type of liner - glassine
• Thickness of liner - 2.79 mils
• Weight of liner - 80g/m2

• 1x 1mm TESA Tape 61395 30 metre roll

Use the adhesive the professionals use for sticking down glass, plastics and cables on mobile and tablet devices. This is a popular tape used by OEM phone and tablet manufacturers

TESA 61395 is a black, double sided self-adhesive tape consisting of a black PET backing and tackified acrylic adhesive.

 

Features:

• 2mm thick
• 30m length
• Thickness: 200µm
• Very high bonding strength
• Superior resistance
• High shock resistance
• Responsive to demanding environmental conditions
• Black color for easy detection
• Pressure activated - heat is not required to form a bond

 

• Back Material - PET film
• Colour - Black
• Adhesive Type - Tackified Acrylic
• Total Width - 2mm
• Total Length - 30 metres
• Total thickness - 7.87 mils
• Elongation at break - 50%
• Tensile Strength - 11.42 lbs/in
• Type of liner - glassine
• Thickness of liner - 2.79 mils
• Weight of liner - 80g/m2

• 1x 2mm TESA Tape 61395 30 metre roll

Use the adhesive the professionals use for sticking down glass, plastics and cables on mobile and tablet devices. This is a popular tape used by OEM phone and tablet manufacturers

TESA 61395 is a black, double sided self-adhesive tape consisting of a black PET backing and tackified acrylic adhesive.

 

Features:

• 4mm thick
• 50m length
• Thickness: 200µm
• Very high bonding strength
• Superior resistance
• High shock resistance
• Responsive to demanding environmental conditions
• Black color for easy detection
• Pressure activated - heat is not required to form a bond

 

• Back Material - PET film
• Colour - Black
• Adhesive Type - Tackified Acrylic
• Total Width - 4mm
• Total Length - 50 metres
• Total thickness - 7.87 mils
• Elongation at break - 50%
• Tensile Strength - 11.42 lbs/in
• Type of liner - glassine
• Thickness of liner - 2.79 mils
• Weight of liner - 80g/m2

• 1x 4mm TESA Tape 61395 50 metre roll

Use the adhesive the professionals use for sticking down glass, plastics and cables on mobile and tablet devices. This is a popular tape used by OEM phone and tablet manufacturers

TESA 61395 is a black, double sided self-adhesive tape consisting of a black PET backing and tackified acrylic adhesive.

 

Features:

• 6mm thick
• 50m length
• Thickness: 200µm
• Very high bonding strength
• Superior resistance
• High shock resistance
• Responsive to demanding environmental conditions
• Black color for easy detection
• Pressure activated - heat is not required to form a bond

 

• Back Material - PET film
• Colour - Black
• Adhesive Type - Tackified Acrylic
• Total Width - 6mm
• Total Length - 50 metres
• Total thickness - 7.87 mils
• Elongation at break - 50%
• Tensile Strength - 11.42 lbs/in
• Type of liner - glassine
• Thickness of liner - 2.79 mils
• Weight of liner - 80g/m2

• 1x 6mm TESA Tape 61395 50 metre roll

Use the adhesive the professionals use for sticking down glass, plastics and cables on mobile and tablet devices. This is a popular tape used by OEM phone and tablet manufacturers

TESA 61395 is a black, double sided self-adhesive tape consisting of a black PET backing and tackified acrylic adhesive.

 

Features:

• 8mm thick
• 50m length
• Thickness: 200µm
• Very high bonding strength
• Superior resistance
• High shock resistance
• Responsive to demanding environmental conditions
• Black color for easy detection
• Pressure activated - heat is not required to form a bond

 

• Back Material - PET film
• Colour - Black
• Adhesive Type - Tackified Acrylic
• Total Width - 8mm
• Total Length - 50 metres
• Total thickness - 7.87 mils
• Elongation at break - 50%
• Tensile Strength - 11.42 lbs/in
• Type of liner - glassine
• Thickness of liner - 2.79 mils
• Weight of liner - 80g/m2

• 1x 8mm TESA Tape 61395 50 metre roll

Use the glue the professionals use for sticking down glass and various plastics on mobile devices.

Appearance: transparent semi-fluid
After curing Hardness: 70-85A
Surface dry time: 6 minutes
Full cure time: 24-48 hours
Storage: stored at 10 degrees to 28 degrees
Shelf Life: 12 Months


Please read carefully before using:

1. The optimum operating temperature should be between 18-32 degrees
2. Experiment on a small area before using on a large surface
3. Make sure that the surface is clean and dry before applying
4. Apply an even amount of glue on the surface.
5. Position two surfaces together and apply pressure for 3-6 minutes
6. Please allow up to 48 hours for optimum adhesive strength

Compatible with:

• Glass
• Plastic
• Acrylic
• Rubber
• Leather
• Ceramics
• Rhinestones
• PE
• PP
• PVC
• ABS

• 1x 15ml B7000 tube of liquid glue